home *** CD-ROM | disk | FTP | other *** search
- D,* - Factory default
- # - User programable
- + - Read only
-
- AT Command Summary
-
-
-
- CMD Function Parameters D
- ------------------------------------------------------------------------------
- AT Attention Code
- A/ Repeat Previous command
- +++ Default escape code
- ------------------------------------------------------------------------------
- A Enter answer mode
- Bn BELL/CCITT(1200bps) 0-CCITT answer tone #
- 1-BELL answer tone
-
- Ds Dial P - Pulse dial * #
- T - Tone dial #
- S - dial Stored string(&Z) #
-
- 0-9, *, #, A-D
- ! - Initiate hook FLASH
- , - Wait time (See S8) 2sec #
- @ - Wait for quiet answer 5sec
- W - Wait for dial tone
-
- ; - Command mode after dial
- R - Answer mode after dial
-
- En ECHO to terminal 0 - No echo in CMD mode #
- 1 - Echo in CMD mode * #
-
- Hn Phone switch hook control 0 - ON hook (hangup) *
- 1 - OFF hook (on-line)
-
- In Identify & check sum 0 - Request modem code
- 1 - Request check sum
- 2 - Request check sum verify
-
- Ln Speaker volume 0 - Speaker, low #
- 1 - Speaker, low #
- 2 - Speaker, medium * #
- 3 - Speaker, high #
-
- Mn Monitor Speaker Control 0 - Speaker always OFF #
- 1 - Speaker On till connect * #
- 2 - Speaker always on #
- 3 - Speaker on after autodial #
- until connect #
-
- O Return to On-Line 0 - Return to On-Line
- 1 - Return to On-Line/Retrain
-
- Qn Result Codes 0 - Result Codes sent * #
- 1 - No result codes #
-
- Sr? Read Register 0 - Rings to answer 000 #
- Sr= Write Register 1 - Rings counter 000
- 2 - Escape Character 043
- 3 - (CR) character 013
- 4 - (LF) character 010
- 5 - (BS) character 008
- 6 - Wait for dial tone n sec 2
- 7 - Wait for carrier n sec 30
- 8 - Pause time (,)sec 2
- 9 - Carrier Det resp. x.1 sec 6
- 10 - Hang up delay x.1 sec 14
- 11 - Not used
- 12 - Esc code guard x.02 sec 050
- 13 - Not used
- 14 - Option register 170 #
- 15 - Not used
- 16 - Modem test options 000
- 17 - Not used
- 18 - Test timer n secs 000 #
- 19 - Not used
- 20 - Not used
- 21 - Bit mapped options 000 #
- 22 - Bit mapped options 118 #
- 23 - Bit mapped options 007 #
- 24 - Not used
- 25 - Delay to DTR sync 005 #
- x.01 sec
- 26 - RTS to CTS delay 001 #
- x.01 sec
- 27 - Bit mapped options 064 #
-
- Vn Result Code Response 0 - Numeric Code #
- 1 - English Text * #
-
- Xn/ Normal/ Extended Result 0 - Basic Set/Blind Dialing #
- 1 - Extended/Blind Dialing #
- 2 - Extended/Dial Tone #
- 3 - Extended/Blind and Busy #
- 4 - Extended/Dial Tone, Busy * #
-
- Yn En Long Sp Disconnect 0 - Long Sp Disconnect Disable * #
- 1 - Long Sp Disconnect Enable #
-
- Z Reset to user configure
-
- &Cn DCD Options 0 - DCD always active * #
- 1 - DCD active carrier detect #
-
- &Dn DTR Options 0 - DTR always ignored * #
- 1 - DTR causes return to CMD #
- 2 - DTR disconnects modem #
- 3 - DTR disconnect and reset #
-
- &F Fetch Factory Config
-
- &Gn Guard Tone 0 - Disable guard tone * #
- 1 - Enable 550Hz guard tone #
- 2 - Enable 1800Hz guard tone #
-
- &Ln Leased/ Dial-up 0 - Dial-up line * #
- 1 - Leased line #
-
- &Pn Pulse Make/Break Ratio 0 - USA, 39% make/61% break * #
- 1 - UK, 33% make/67%break #
-
- &Rn RTS/CRT Handshake 0 - CTS Always active * #
- 1 - CTS Always active #
-
- &Sn DSR Options 0 - DSR always active * #
- 1 - DSR active at connect #
-
- &Tn Test Commands 0 - Terminate test *
- 1 - Local analog loopback
- 2 - Reserved
- 3 - Local digital loopback
- 4 - Enable Rmt digital loop * #
- 5 - Disable Rmt digital loop #
- 6 - Request Rmt digital loop
- 7 - Request Rmt digital loop
- and enter self-test
- 8 - Local analog loopback
- and enter self-test
-
- &W Write config to memory
-
- &Zn Store Phone Number #
-
-
- AT Command Summary Result Codes
-
- NBR English Text x0 x1 x2 x3 x4
- ---------------------------------------------------------------
- 0 OK Y Y Y Y Y
- 1 Connect Y Y Y Y Y
- 2 Ring Y Y Y Y Y
- 3 No Carrier Y Y Y Y Y
- 4 Error Y Y Y Y Y
- 5 Connect 1200 - Y Y Y Y
- 6 No Dial Tone - - Y - Y
- 7 Busy - - - Y Y
- 8 No Answer - Y Y Y Y
- 9 Connect 600 - Y Y Y Y
- 10 Connect 2400 - Y Y Y Y
-
